What is the vibration resistance of a PCB - Relay?

Nov 16, 2026Leave a message

If you’ve ever worked on a machine that shakes—think a vending machine, a portable industrial tool, or a car’s dashboard electronics—you know the last thing you want is a part that quits mid-job. As a PCB relay supplier, I get questions about vibration resistance all the time: how does it work, why does it matter, and what should you actually look for when picking a relay that won’t let you down in a moving or jostling setup? Let’s break this down without all the stuffy engineering jargon that makes your eyes glaze over.

First, let’s keep it simple: PCB relays are those tiny, plug-and-switch components mounted right on a printed circuit board (PCB), right? Their whole job is to turn circuits on or off using an electromagnet, which means they have moving parts—contacts, armatures, springs, the whole works. That’s where vibration becomes a problem. If your relay rattles around too much, those moving parts can knock out of place, the contacts might bounce (which causes arcing or even a full switch failure), or the solder joints holding it to the PCB could crack. Not great, especially if your equipment’s running 24/7.

So what exactly is “vibration resistance” for a PCB relay? It’s basically how well that little component holds up when it’s being shaken. We measure it using two main specs people care about: frequency and acceleration. Frequency is how fast the vibration is happening (in Hz, like how many times per second something shakes), and acceleration is how hard it’s shaking (in Gs—1 G is the same as gravity pulling you down when you drop a pen). For most industrial or automotive setups, you’ll be looking at 10 to 2000 Hz and anywhere from 10 to 50 Gs. Cheaper relays might barely hit 10 Gs before failing, but the good ones (like the ones we stock) go way higher, designed to keep working even when your equipment’s bouncing around in a truck on a rough road or vibrating nonstop in a factory conveyor.

Wait, but not all relays are built the same, right? Let’s use some real examples of what we carry to make this concrete. Take our 12V Single-Pole, Double-Throw Relay—it’s a workhorse for small circuits, and it’s rated for up to 30 Gs of continuous vibration. That means if you mount this on a portable device that gets tossed around during shipping, or a robot arm that moves a lot, it’s not going to just stop working because of a little shake. I’ve seen guys use this specific relay for vending machine coin mechanisms, which jolt every time someone inserts a dollar bill, and they haven’t had a single vibration-related failure in over a year.

Another big one is our Wholesale PCB Relay 20A. This is the go-to for bulk orders, and since we build these with reinforced solder tabs and tighter contact springs, it handles up to 40 Gs. For context, that’s like shaking the relay as hard as a car hitting a pothole at 50 mph nonstop. It’s perfect for things like HVAC systems or power tools that vibrate a lot during operation, and since it’s wholesale, you don’t have to break the bank when you need 100 or 1000 of them.

T90 Relay 12v 24v 6 PinWholesale PCB Relay 20A

Now, let’s talk about what actually makes a relay vibration-resistant. It’s not just random luck—there’s engineering behind it. First, the contact design. Relays that have more tightly sprung contacts and maybe even gold-plated contact points (for better conductivity and less wear) don’t bounce as much when shaken. Bouncing contacts are a big deal because when they open and close too fast from vibration, they create tiny arcs that can melt the metal over time, leading to failure. Then there’s the mounting: relays designed for PCBs have reinforced pin structures so the solder joints don’t crack. If the pins are flimsy, even a little vibration can snap the solder connection.

Also, the armature (the part that moves to toggle the switch) and the coil assembly need to be secured tight. We use epoxy to lock those parts in place on all our mid-range and premium relays, which stops them from shifting around when shaken. The cheap no-name relays out there skip this step, so their armatures can rattle loose and jam the switch entirely. I’ve had a customer come to us once with a batch of 500 cheap relays that failed in a test because their armatures just vibrated off their mounts—we replaced them with our T73 PCB Relay 24vdc, and none of those had issues. That model’s rated for 45 Gs, by the way, so it’s built for heavier-duty vibration.

Wait, but do you really need a super high-vibration relay for every job? No, that’s a waste of money. If your equipment’s sitting on a bench in a lab, shaking is almost zero, so a basic relay works fine. But if it’s going to be in a car, a construction tool, a portable generator, or anything that moves or vibrates a lot, you need to match the relay’s vibration rating to your application. Let’s say you’re wiring a car’s interior lights—our T90 Relay 12v 24v 6 Pin is designed for automotive use, and it’s tested up to 50 Gs, which is exactly what you need for the constant vibration of a driving vehicle. That’s the kind of relay that won’t leave you stranded on the side of the road because the interior light switch died from road vibration.

Another thing that people don’t think about: shock and vibration are different, but they’re related. Shock is a sudden, hard jolt (like dropping a device), while vibration is constant shaking. A relay that’s good at handling vibration will usually handle shock too, but not always. For example, our 30A12V Relay 4-Pin is rated for 50 Gs vibration and up to 100 Gs shock, which means it can take being dropped off a workbench and still work. That’s why electricians and engineers love this one for temporary job-site equipment—they drop it, bump it, and it keeps going.

Now, let’s bust a common myth: higher amperage doesn’t automatically mean higher vibration resistance. Sure, a 30A relay is bigger and has heavier parts, but only if it’s built with vibration in mind. We’ve seen big, cheap 30A relays that fail at 10 Gs, while our smaller 20A relay holds up at 40 Gs because of better internal design. The key specs to check aren’t just the amp or voltage rating—look for the vibration test numbers. Most reputable suppliers (like us) list that right on the product page, so you don’t have to guess.

So, what should you do if you’re not sure which relay you need for your vibration-prone application? First, figure out how much vibration your equipment actually has. If you’re working on something like a laptop (barely any vibration), a basic low-cost relay works. If it’s a forklift or a medical device with moving parts, you’ll want at least 30 Gs. If it’s a heavy-duty conveyor system or agricultural equipment, go for 50 Gs or higher. And when in doubt, reach out—we’ve helped tons of guys pick the right relay for their setup, no sales pitch, just honest advice.

I’ve been working with PCB relays for over 10 years now, and the number one reason customers come to us is because their previous relays failed due to vibration. It’s such a preventable issue—most of the time, they just picked the wrong relay because they didn’t check the vibration rating. Don’t be that guy who has to rework a whole circuit because a cheap relay rattle itself to pieces.

If you’re ordering in bulk, make sure to ask for test data. Any good supplier should be able to show you their vibration testing reports—we can send those for every model we carry. We also offer custom configurations for specific applications, so if you have something that’s extra vibration-heavy, we can adjust the contact springs or mounting to meet your needs.

At the end of the day, vibration resistance for a PCB relay is all about reliability. You don’t want your equipment to fail because a tiny part can’t handle a little shake. Whether you need a single relay for a small project or thousands for a big production run, we’ve got options. Our inventory includes everything from the compact 12V Single-Pole, Double-Throw Relay for light-duty jobs to the heavy-duty 30A12V Relay 4-Pin for the toughest vibration environments. We also have the T73 PCB Relay 24vdc and T90 Relay 12v 24v 6 Pin for mid-range to high-demand setups, all with verified vibration ratings you can trust.

If you’re tired of replacing relays because of vibration, or you just need help picking the right one for your application, get in touch with our team. We’re here to answer questions, share test data, and make sure you get a relay that works for your setup—no fluff, no hidden fees, just solid products that hold up when the going gets shaky. Don’t waste time and money on relays that can’t handle the job; let’s find the right solution together.

References

  1. International Electrotechnical Commission. (2018). IEC 60947-5-1: Low-voltage switchgear and controlgear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices.
  2. American National Standards Institute. (2020). ANSI C119.4: Relays for Use in Electrical Power Systems.
  3. Bosch Automotive Electrics. (2019). Application Guidelines for Relays in Mobile Vibration Environments.
  4. PCB Design Magazine. (2021). “Vibration Resistance Considerations for Surface-Mount Relays.”