
To calculate the correct heat sink for an SSR, calculate the relay's real average power loss, define the worst local ambient temperature and a permitted junction-temperature design limit, then allocate the remaining thermal resistance to the heat sink. For one steady-state thermal path, the basic result is:
Maximum heat-sink resistance:
RθSA,max = (Tj,design − Ta,max) / Ploss − RθJC − RθCS
Choose a heat sink with an RθSA value equal to or lower than the result under the same airflow, orientation, source area and mounting conditions. Then verify the exact SSR/heat-sink combination with its derating curve and a worst-case temperature-rise test.
When you calculate a heat sink for an SSR, rated current alone is not enough. An AC thyristor or triac SSR often uses an on-state-voltage loss model, while a DC MOSFET SSR normally uses current squared times hot on-state resistance. The calculation also changes with switching method, duty cycle, phase count, shared heat sinks, cabinet temperature and airflow.
Electrical and thermal safety: SSRs may switch hazardous mains or high-energy DC, can remain hot after power is removed and may fail in a conductive state. Do not touch, wire, remove or test a live SSR or heat sink. Final selection, protective devices, enclosure/earthing, mounting and commissioning must follow the exact product instructions and be completed by qualified personnel.
SSR Thermal-Resistance Chain at a Glance
|
Term |
What It Means |
Where to Get It |
|---|---|---|
|
Tj,design |
The junction-temperature limit chosen for the design, normally below or no higher than the product's permitted maximum. |
Exact SSR data sheet plus the project's reliability margin and fault consequences. |
|
Ta,max |
Worst local air temperature around the heat-sink inlet-not automatically room temperature. |
Cabinet heat study, measured installation data or a conservative verified requirement. |
|
Ploss |
Average heat generated inside the SSR for the real current waveform and operating profile. |
Manufacturer loss curves, on-state voltage data, hot RON data or an approved waveform calculation. |
|
RθJC or RθJB |
Thermal resistance from the semiconductor junction to the manufacturer-defined case or base reference. |
Exact SSR data sheet; never copy a value from another package or current class. |
|
RθCS |
Case/base-to-sink resistance through the thermal pad, grease and mechanical interface. |
Qualified interface data or the SSR/heat-sink manufacturer's tested assembly. |
|
RθSA |
Heat-sink-to-ambient resistance; this is the main heat-sink selection target. |
Heat-sink data under stated airflow, orientation, mounting and heat-source conditions. |
Thermal resistance is expressed in °C/W or K/W. The numerical value is the same for a temperature difference: a lower number means less temperature rise per watt and therefore greater cooling capability under comparable test conditions. A 1 °C/W sink is more capable than a 3 °C/W sink only when both ratings use comparable airflow and mounting conditions.
1. Why an SSR Needs a Thermal Calculation
An SSR has no mechanical contact gap while it conducts. Its output semiconductor has an on-state voltage or resistance, so current through the device creates heat. That heat travels from the semiconductor junction through the SSR base, the mounting interface and the heat sink before reaching the surrounding air.
Sensata/Crydom's heat-sink and SSR assembly guide explains that heat-sink thermal performance is stated in degrees Celsius per watt, and that published natural-convection performance depends on airflow over the fins. Its guidance also shows why the interface material and mechanical mounting belong to the thermal system.

A panel-mount SSR, interface pad and finned heat sink form one thermal assembly. This pictured product is an external example, not a QIANJI model or sizing recommendation. Image: Relequick solid state relay with heatsink by Relequick relays, licensed under CC BY-SA 4.0 via Wikimedia Commons.
The front-label current rating may assume a particular heat sink, ambient temperature, airflow and load. It is not a promise that the SSR can carry that current on any metal panel. A smaller heat sink, hotter cabinet or poor thermal interface can lower the allowable load current substantially.
2. Use One Compatible Junction-to-Ambient Thermal Path
For one SSR at thermal steady state, a useful simplified relationship is:
Tj ≈ Ta + Ploss × (RθJC + RθCS + RθSA)
The model acts like a series path: each watt produces a temperature rise across each thermal resistance. Rearranging it gives the maximum allowable RθSA shown at the beginning of this guide.
Do not add RθJA to RθJC plus a heat sink. Junction-to-ambient resistance normally describes a different complete reference condition, often a device in free air or on a defined test mounting. It is not another physical segment to place in series with the selected heat sink. Use one consistent path with definitions from the same product documentation.
This steady-state model also does not describe every short pulse. If the SSR operates intermittently or experiences high transient power, the data sheet's transient thermal impedance or manufacturer model may be required. Thermal mass can delay temperature rise without changing the final steady-state requirement.
3. Calculate SSR Power Loss for the Actual Output Technology
AC thyristor or triac SSR loss
For many AC on/off SSRs, a first estimate is:
Ploss ≈ VON × IRMS
Use the applicable on-state voltage at the actual current and condition. Confirm whether the number is typical or maximum and whether the data sheet provides a more accurate curve or model. Celduc's heat-sink selection white paper uses a more detailed voltage-threshold plus dynamic-resistance model for AC outputs. That manufacturer-specific method is preferable when its required parameters are available.
For full-cycle burst control, average heat may be related to the actual ON fraction, but waveform and duty definitions must match the manufacturer's curve. Phase-angle control, chopped waveforms, motors, transformers and capacitive loads cannot be reduced safely to a generic nameplate-current multiplication. Use the vendor's loss data for the topology and switching method.
DC MOSFET SSR loss
For a MOSFET-output SSR, conduction loss is commonly estimated as:
Ploss ≈ I2 × RON(Tj)
Current is squared, and MOSFET on-state resistance generally rises as junction temperature increases. Use the total hot resistance of the complete SSR output-not a room-temperature RDS(on) copied from an unrelated transistor. OMRON's SSR technical explanation identifies both the I²R loss relationship and the temperature dependence of MOSFET on-state resistance.
Three-phase, PWM and special loads
A multi-channel SSR generates heat in every active output path. Use the exact three-phase or multi-channel loss and derating data, or calculate each channel consistently and sum the heat seen by a common sink. High-frequency PWM adds switching loss; phase control changes the current waveform; abnormal inrush and commutation can impose separate electrical stress. A thermal calculation does not replace surge, I²t, dv/dt, protection or load-compatibility checks.
4. Worked AC SSR Heat-Sink Calculation
This example demonstrates the method only. Every value is assumed and must be replaced with data from the exact SSR, interface, load and installation. It is not a recommendation for a 20 A application.
|
Assumed Input |
Example Value |
Purpose |
|---|---|---|
|
Actual RMS load current |
20 A |
Expected continuous current through one AC SSR channel. |
|
Applicable on-state voltage |
1.2 V |
Hypothetical value at the relevant current and temperature. |
|
Estimated SSR loss |
24 W |
Ploss = 1.2 V × 20 A. |
|
Selected junction design limit |
125 °C |
Hypothetical engineering limit; the exact SSR controls. |
|
Worst local ambient |
40 °C |
Air temperature around the sink within the design envelope. |
|
RθJC + RθCS |
0.8 + 0.2 °C/W |
Hypothetical device and interface resistances. |
First calculate the total allowable junction-to-ambient resistance:
(125 − 40) / 24 = 3.54 °C/W
Then remove the thermal resistance already used inside the SSR and interface:
RθSA,max = 3.54 − 0.8 − 0.2 = 2.54 °C/W
The installed heat sink must therefore be rated at 2.54 °C/W or lower under the real conditions. If a verified 2.0 °C/W sink is selected, the simplified predicted junction temperature is 40 + 24 × (0.8 + 0.2 + 2.0) = 112 °C. That creates 13 °C of margin to the assumed 125 °C design limit-but only if every assumed value and test condition is valid.
Sensata's EL Series AC SSR data sheet demonstrates why exact product data matter: its published on-state drop and junction-to-case resistance vary by current class. Do not transfer one RθJC value across an entire SSR family.
5. Worked DC MOSFET SSR Loss Example
Assume a DC SSR carries 15 A continuously and its total on-state resistance is verified as 12 mΩ at the relevant operating temperature. The illustrative conduction loss is:
Ploss = 152 × 0.012 = 2.7 W
This loss is much lower than the preceding 24 W AC example, but the comparison does not prove that every DC SSR runs cooler. Voltage class, internal MOSFET arrangement, hot resistance, surge behavior, PWM frequency, package and thermal path all change the result. Continue with the same Rθ budget using the exact DC SSR's RθJC, interface and permitted temperature data.
Also check whether reverse current, inductive energy, regeneration or an output protection component adds heat or voltage stress. A heat sink cannot correct an SSR that has the wrong voltage polarity, load category or switching topology.
6. Use the Calculation and the Manufacturer's Derating Curve
The resistance calculation explains the thermal budget and helps compare options. The manufacturer's load-current-versus-ambient curve accounts for the specific package, semiconductor, base construction and defined heat sink or mounting plate. Use both.
If the exact product documentation lists an approved SSR/heat-sink combination, begin there. Confirm the curve uses the same local ambient, airflow, orientation, interface and load mode. OMRON states that a commercial heat sink may substitute for a specified heat sink only when its thermal resistance is equal to or lower than the reference value. That comparison is meaningful only when the rating conditions are comparable.
IEC 62314:2022 defines safety-related and functional requirements for SSR components within its scope. The IEC publication record also makes clear that an SSR component is incorporated into equipment that must meet its relevant product or application standards. A heat-sink calculation does not by itself establish end-equipment compliance.
7. Installation Factors That Change Heat-Sink Performance
|
Installation Factor |
Why It Changes the Result |
Required Action |
|---|---|---|
|
Thermal pad or compound |
Air gaps add interface resistance; pad/grease material, thickness and coverage matter. |
Use the SSR maker's approved interface and include RθCS or its qualified assembly curve. |
|
Flatness and mounting torque |
Insufficient pressure leaves gaps; excessive or uneven torque can distort or damage the package. |
Follow exact surface and tightening instructions; do not publish or reuse a generic torque. |
|
Fin orientation and clearance |
Natural convection needs an open vertical airflow path; blocked or horizontal fins perform differently. |
Match the rated orientation and spacing or validate the changed arrangement by test. |
|
Cabinet ambient |
Nearby power devices heat the local air above the room temperature. |
Use the worst local air temperature and evaluate the total enclosure heat balance. |
|
Material, finish and source area |
Aluminum spreads heat differently from ordinary steel; coating and source footprint affect performance. |
Use a qualified sink or validated plate; do not assume any painted backplate is equivalent. |
|
Altitude and forced airflow |
Air density, true velocity, bypass, filter loading and fan failure change convection. |
Apply the supplier's derating and define detection or a safe response to lost airflow. |
Sensata's panel-mount SSR installation guide calls for a suitable thermal pad or compound and vertical fins for natural convection. The dimensions and torque in any one installation guide belong only to the covered product family; the principle transfers, but the numbers do not.
![]()
Heat-sink fins increase surface area, but the published RθSA still depends on orientation, airflow and how heat enters the extrusion. Image: Aluminium heatsink, 76x50mm cross-section by Retired electrician, dedicated under CC0 1.0 via Wikimedia Commons.
8. Can Multiple SSRs Share One Heat Sink?
Yes, but the common sink must reject the sum of the average losses from all simultaneously active SSR channels. A first system-level estimate is:
ΔTsink ≈ Ptotal × RθSA
Then calculate each device's junction temperature from that elevated sink temperature plus its own Ploss × (RθJC + RθCS). Do not multiply one SSR's RθJC by the number of devices; that internal resistance belongs to its own junction path.
Position and spacing matter because heat does not spread perfectly across a real extrusion. One SSR can sit in a hotter local zone or receive preheated air from another. Celduc's current thermal-management guidance recommends adding total dissipated power for shared heat sinks and confirming the result with a worst-case temperature-rise test.
For a three-phase SSR, do not assume the front label represents one thermal source. Use the manufacturer's multi-phase derating curve and simultaneous-channel conditions. If individual SSRs share the same heat sink, also check whether their baseplates require electrical isolation and whether the common metalwork creates an earthing or clearance issue.
9. Natural Convection or Forced Air?
Natural convection is simple and avoids a fan as a wear item, but it may require a larger sink and more spacing. Forced air can reduce effective thermal resistance and assembly size, but the quoted RθSA is valid only at the specified airflow through the real fin channel.
State air velocity or volume flow, fan curve, pressure drop, filter condition and airflow direction. Define what happens if the fan stalls, a filter blocks, a door opens or a wiring bundle bypasses the fins. Options may include detection, alarm, controlled load reduction, shutdown or a heat sink capable of a defined reduced-load natural-convection mode.
Do not convert a forced-air rating to a natural-convection rating with an informal percentage. If the supplier offers only a rough airflow improvement factor, treat it as a planning aid and verify the production enclosure. Altitude can also reduce cooling performance because lower air density changes convection and fan behavior.
10. How to Validate the SSR and Heat Sink
A calculation is a design model. The final evidence is a temperature-rise test using production-intent parts and the worst credible operating profile. The test should include the exact SSR, heat sink, thermal interface, hardware, torque, enclosure, spacing, local ambient, electrical current/waveform and number of active channels.
- Freeze the configuration. Record part numbers, data-sheet revisions, thermal pad/compound, heat-sink finish, mounting method and airflow.
- Apply the worst credible load. Use actual RMS or DC current, duty cycle, switching mode, phase count, adjacent heat sources and simultaneous channels.
- Control or record local ambient. Measure the air that cools the sink, not only room temperature outside the enclosure.
- Wait for thermal steady state. A short bench run may look safe only because the heat sink and cabinet have not finished warming.
- Measure documented locations. Follow the SSR maker's base/case measurement method and record heat-sink temperature near every device.
- Estimate junction temperature only as permitted. If the manufacturer authorizes a case-temperature-plus-RθJC calculation, use its exact reference point and model.
- Test adverse conditions. Include foreseeable airflow loss, hot neighboring channels or maximum duty when these belong to the design envelope.
- Document acceptance. Record instruments, uncertainty, duration, ambient, current, temperatures and required corrective action.
![]()
A contact temperature sensor can support a controlled thermal test, but its placement, attachment, insulation and instrument uncertainty must be defined. Image: Thermocouple by Maria Di Nezza, licensed under CC BY 4.0 via Wikimedia Commons.
An infrared camera can help locate hot regions, but reflective aluminum, anodized surfaces, labels and viewing angle can produce emissivity errors. Use it as a screening tool unless the measurement method has been calibrated for the surface. Do not call an arbitrary surface temperature the semiconductor junction temperature.
11. Common SSR Heat-Sink Mistakes
|
Mistake or Symptom |
Why It Fails |
Better Practice |
|---|---|---|
|
Selecting from SSR current rating only |
The rating may assume a specified sink, ambient, load and airflow. |
Calculate real Ploss, thermal resistance and product derating. |
|
Using room temperature as Ta |
Air beside the heat sink can be much hotter inside a loaded cabinet. |
Measure or conservatively establish worst local ambient. |
|
Adding RθJA to the heat-sink chain |
RθJA normally represents a different complete reference condition. |
Use one compatible junction-case-interface-sink-ambient path. |
|
Ignoring hot MOSFET resistance |
I²R loss rises as current and on-state resistance increase. |
Use RON(Tj) or the exact product's loss curve. |
|
Mounting on painted steel without validation |
Poor spreading and uncertain interfaces can make the panel a weak sink. |
Use a qualified aluminum sink/plate or validate the full assembly. |
|
Sharing a sink without adding total loss |
Every active SSR raises common sink and inlet-air temperature. |
Sum heat, calculate each junction path and test all channels. |
|
Assuming the fan always delivers its label flow |
Filters, pressure, bypass, dust, voltage and failure change actual airflow. |
Validate the real flow path and define a fan-failure response. |
OMRON's SSR safety precautions warn against touching an energized or recently energized SSR/heat sink and require power isolation before wiring. They also warn that a load-side short circuit can seriously damage an SSR. Thermal design must therefore be paired with appropriate overcurrent protection and a system response to a conductive SSR failure.
12. SSR Heat-Sink Selection Workflow
- Identify the output technology and load. AC triac/SCR, DC MOSFET or another topology; resistive, inductive, capacitive or defined waveform.
- Define the electrical profile. Voltage, actual RMS/DC current, inrush, switching mode, duty cycle, phases and simultaneous channels.
- Calculate or obtain Ploss. Use product-specific curves or validated hot electrical parameters.
- Set Ta,max and Tj,design. Use local cabinet air and an engineering limit supported by the exact data sheet.
- Build the complete thermal chain. Confirm RθJC, interface material/RθCS and the required RθSA,max.
- Select under comparable conditions. Match airflow, orientation, source area, mounting and altitude; choose suitable margin.
- Check derating and protection. Confirm the product curve, short-circuit protection, load surge and end-equipment requirements.
- Validate the production assembly. Run a steady-state temperature test with the real enclosure and worst credible load.
No universal safety-margin percentage replaces these steps. Margin must cover uncertainty in loss data, current, ambient, airflow, interface quality, dust, aging and production variation, as well as the consequence of overheating.
13. What to Include in an SSR and Heat-Sink RFQ
- Load: heater, motor, transformer, solenoid, capacitor, DC load or defined waveform; nominal/maximum voltage and current.
- Switching duty: zero-cross, instant/random, burst, phase-angle or PWM; frequency, duty cycle, surge/inrush and simultaneous phases/channels.
- SSR data: required output technology, voltage/current class, VON or hot RON, surge/I²t, leakage, control input, protection and approvals.
- Thermal environment: maximum local ambient, cabinet heat, altitude, orientation, natural/forced airflow, fan/filter details and nearby heat sources.
- Thermal path: RθJC, interface material and thickness, required RθSA, sink material/finish, flatness, hardware and approved torque.
- Shared sink: number and position of SSRs, maximum simultaneous current and any baseplate isolation/earthing requirement.
- Validation: derating curve, supplier loss calculation, measurement point, temperature acceptance criteria, test report and production sample.
- Commercial: prototype and annual quantity, assembly preference, certifications, traceability, change control, lead time, spares and warranty.
QIANJI's verified solid-state relay category can be used to identify candidate output types and packages. For a useful thermal review, send the exact SSR model or candidate, load waveform/current, maximum cabinet ambient, active channel count, enclosure layout and airflow through the QIANJI inquiry page. The broader QIANJI product range should not be used as a substitute for a current data sheet.
Send these six items first: SSR part number, load type, actual RMS/DC current, switching duty, maximum local cabinet ambient and number of simultaneously active channels. Without them, a heat-sink recommendation is only a guess.
Frequently Asked Questions
How do I calculate SSR heat-sink size?
Calculate average SSR loss, define the maximum local ambient and junction design limit, then solve RθSA,max = (Tj,design − Ta,max) / Ploss − RθJC − RθCS. Select an equal or lower heat-sink resistance under matching conditions, check the exact derating curve and validate the assembly thermally.
What is the AC SSR heat-loss formula?
A common first estimate is Ploss ≈ VON × IRMS. Use the applicable on-state voltage and actual current. If the manufacturer supplies a voltage-threshold/dynamic-resistance model or loss curve, use that product-specific method for the final design.
What is the DC MOSFET SSR heat-loss formula?
Use Ploss ≈ I² × RON(Tj) for conduction loss, using the complete SSR's on-state resistance at the relevant temperature. Add switching or other loss only through the product's approved model.
Does every SSR need a heat sink?
No. Some low-current SSRs can operate without an external heat sink under defined ambient and load conditions, while panel-mount power SSRs often require one. Follow the exact product's load-current-versus-ambient curve and mounting instructions.
Can I mount an SSR directly on a metal backplate?
Only when the manufacturer's data supports the plate material, dimensions, thickness, finish, interface, ambient and load. Painted steel is not automatically equivalent to an aluminum heat sink. Validate the final assembly.
Is a lower °C/W heat-sink number better?
Yes under comparable test conditions. Lower RθSA means less heat-sink temperature rise per watt. Do not compare a forced-air rating directly with a natural-convection rating or ignore orientation and source area.
How much thermal safety margin should I use?
There is no universal percentage. Margin should cover component tolerance, current/duty variation, local ambient uncertainty, interface quality, airflow degradation, altitude, aging and the consequence of failure. Define it through the system risk and validation process.
Do I need thermal grease or a thermal pad?
Use the exact SSR manufacturer's approved interface. Both can reduce air gaps, but their thermal resistance, thickness, compression and assembly rules differ. Include RθCS or use the qualified assembly curve.
Can multiple SSRs share one heat sink?
Yes if the sink is sized for total simultaneous loss and every SSR's local junction path is checked. Position, spacing, spreading resistance, airflow, baseplate isolation and all-channel operation require validation.
Final Recommendation
The correct SSR heat sink is the one that keeps the exact device below its selected junction-temperature limit at the real current waveform, switching profile, local cabinet ambient, mounting arrangement and airflow. Start with product-specific power loss, solve the complete compatible thermal-resistance chain, and choose an RθSA lower than the maximum calculated value under matching conditions.
Then check the manufacturer's derating curve and test the production-intent assembly at thermal steady state with all relevant channels operating. Treat the interface, torque, orientation, enclosure air, spacing, altitude and fan condition as design inputs-not installation details to decide later.
Technical References
- IEC 62314:2022 - scope and safety/functional requirements for solid-state relay components.
- Sensata/Crydom: Heat Sinks & SSR Assemblies - thermal-resistance meaning, assembly path and convection conditions.
- OMRON: Further Information of Solid-state Relays - AC conduction loss, MOSFET I²R loss, heat-sink comparison and interface guidance.
- Celduc: Heat Sink Selection White Paper - loss models and heat-sink thermal-resistance calculation.
- Sensata: EL Series AC Output SSR Data Sheet - product-family example of on-state voltage, RθJC and derating data.
- Sensata: AC Panel-Mount SSR Installation Guide - interface, surface, mounting and fin-orientation requirements.
- Celduc: Thermal Management - shared heat sinks, airflow and worst-case temperature-rise testing.
- OMRON: SSR Safety Precautions - heat, electrical shock, wiring isolation and short-circuit precautions.
